Installation Instructions Pdf
Bontrager Fender Installation Instructions Free
Bontrager Fender Installation Instructions Diagram

Two of our folding bike models, the Navigator and the Boston 8, feature quick release fenders on the front and rear. Fenders are an absolute necessity if you’re riding in foul weather, but even a wet road after the rain can leave you with soggy shoes and pants if you don’t have the proper protection. Our quick release fenders can now be purchased for use with any of our Pavement Bikes. Your FIT, Crosstown, or single speed Boston can now offer that same protection from rainwater and road grime.

Full coverage bicycle fenders, quick mount individual fenders - Planet Bike offers many sizes of fenders to keep you clean and dry on your ride. Enhance your cycling experience with Bontrager NCS Fender Set. Find the best gear at trekbikes.com and your local Trek retailer. Enhance your cycling experience with Bontrager NCS Fender Set. Find the best gear at trekbikes.com and your local Trek retailer.

Bontrager Fender Installation Instructions

For easy removal, these fenders clip onto brackets that mount using the brake caliper bolts. The installation procedure might not be obvious at first, but it’s fairly simple. If you purchase one of our aftermarket fender kits, it will include some extra hardware. The only pieces you will need are the fenders themselves, and these two brackets:

Start by removing the front brake caliper with a 5mm allen key:

Once the caliper is free, the front bracket (shown below) can be installed. It will pass under the fork crown, with the clip in the rear:

To secure it, pass the brake caliper bolt through the slot in the bracket, and thread the nut back on from the back:

Arm and hammer anvil serial numbers. Your serial number 38508 would put the production year within 1922-1923 Arm and Hammer anvils share many of the same shapes and qualities of Trenton anvils. Columbus Anvil and Forging Co. Was actually started by a former employee and anvil maker for Columbus Forge and Iron Co. (Trenton) They were neighbors and even had some forgings done at. The wrought Arm and Hammer Anvil is often confused with the cheaper cast Vulcan anvil. It is a American made steel faced wrought iron bodied anvil made by the Columbus Anvil and Forging company of Columbus, OH. They made anvils from 1900. Apr 7, 2015 - Explore JJ's board '208 lb Pound Arm and Hammer Anvil' on Pinterest. See more ideas about arm and hammer anvil, arm & hammer, anvil.

Installation Instructions Pdf

Now you can slide the fender in the clip, and close the lever to lock it:

Installing the rear fender is a similar procedure, but the bracket is a bit different. Again, start by removing the brake caliper:

With the aftermarket fender kit, you’ll have an extra bracket (one more than you need). The correct one for the rear is the longer, narrow, two-prong bracket. The narrower bracket is designed to prevent any interference when folding the bike. The slotted section of the bracket goes between the brake and the frame, and the rest extends up and over the top of the brake caliper. Thread the nut back onto the brake caliper from the underside, and tighten it up:

The rear fender has the clip built in. Slide it onto the bracket, and close the lever. If either of your fenders seem off center from the wheel, you can correct that by loosening the brake caliper bolt, and rotating the bracket:

There you have it, protection from the elements, and easy, quick release removal:

Bontrager Fender Installation Instructions Free

Bontrager Fender Installation Instructions Diagram

Made of durable polycarbonate and featuring the highest quality hardware of any fenders in their class, Portland Design Works' Poncho Fenders keep you safe from spray from head to toe. They use thick 6mm stays for extra rigidity, sturdy rubber mudflaps for extra coverage, and front safety release tabs to ensure your wheels keep turning even if debris gets lodged between the fender and tire. The Road size Poncho Fenders will fit close clearance road bikes with 700x23 tires maximum or road bikes designed to take fenders with up to 700x25 tires. They are designed to fit under caliper brakes and forks, and include add-on mounts for bikes that lack eyelets.- 30 mm wide to fit 700x23 tires maximum- Pre-installed stays and brackets for faster mounting- Weight: 454 g (16 oz)- Lifetime PDWarrantyThe City size Poncho Fenders are designed for touring and CX bikes with 700x35 tires maximum. They come with all necessary hardware to mount to bikes with brazed on eyelets.- 45 mm wide to fit 700x35 tires maximum- Pre-installed stays and brackets for faster mounting- Weight: 567 g (20 oz)- City size installation manual (PDF)- Lifetime PDWarranty